Electrical Cost in Fort Pierce, FL
Electrical Cost in Fort Pierce, FL
An electrician in Fort Pierce typically charges $150 to $400 for a service call and diagnosis, and $85 to $150 per hour. A 100-amp to 200-amp panel upgrade is typically $1,800 to $3,500. A Level 2 EV charger is typically $1,000 to $3,500 in total for most homes. All ranges in this guide were checked November 9, 2026. They are typical ranges, not promises. Call (877) 631-1186 for your exact range after we see the job.
Call (877) 631-1186 — 24/7, English only.
Last updated: November 9, 2026
How to use this guide
Read the table first. Then read the section for your job. Prices are ranges because houses are different. A clean panel, a short run, and easy access keep a price down. A rusted panel, a long run, and a permit push it up.
We price every job in writing before we start. No free estimates. We respond fast — just a call away.
Sunrise City Electric is licensed and insured, license EC13022015, with 15 years in business. Owner: Michael Bennett. Call (877) 631-1186, 24/7, English only.
The full cost table
Typical ranges, checked November 9, 2026. Not promises.
| Job | Typical range |
|---|---|
| Service call / diagnosis | $150 to $400 |
| Hourly rate | $85 to $150 per hour |
| Outlet replacement | $95 to $150 |
| Switch replacement | $95 to $200 |
| GFCI replacement | $95 to $200 |
| Breaker replacement | $150 to $300 |
| Ceiling fan installation | $200 to $500 |
| Light fixture installation | $150 to $400 |
| Recessed lighting, per light | $150 to $300 |
| Panel upgrade, 100 amp to 200 amp | $1,800 to $3,500 |
| Panel upgrade, 200 amp to 400 amp | $3,500 to $7,000 |
| Federal Pacific panel replacement | $2,000 to $5,000 |
| Zinsco panel replacement | $2,000 to $5,000 |
| Subpanel, installed | $800 to $2,000 |
| Whole-home surge protector, installed | $200 to $800 |
| EV charger, Level 2, total for most homes | $1,000 to $3,500 |
| EV charger, basic install | $850 to $1,750 |
| EV charger, complex install | $2,750 to $7,200 |
| Generator inlet and interlock, installed | $500 to $2,400 |
| Manual transfer switch subpanel | $1,500 to $2,500 |
| Standby generator, 11 to 14 kW | $6,500 to $9,500 |
| Standby generator, whole-home 18 to 24 kW | $9,500 to $18,000 |
| Full home rewire | $8,000 to $20,000 |
| Aluminum wiring remediation | $1,500 to $4,000 |
| Smoke / CO detector, hardwired, per unit | $100 to $250 |
How much does an electrician cost per hour in Fort Pierce?
Typically $85 to $150 per hour. A service call and diagnosis is typically $150 to $400. That covers the visit, the testing, and the diagnosis.
An hourly rate does not tell you the job price. A simple repair takes less than an hour. A fault that takes time to find takes longer. We tell you the time and the price before we start.
How much is a panel upgrade?
100 amp to 200 amp: $1,800 to $3,500
This is the most common panel upgrade in Fort Pierce. A 100-amp panel in a house from the 1960s or 1970s cannot carry a modern load. A 200-amp panel can, in most cases.
What is in the price: the new panel, new breakers, the permit, the meter pull, and the inspection. What moves it up: a rusted panel, corrosion, a long run from the meter, wiring that has to be replaced, and a difficult meter pull.
200 amp to 400 amp: $3,500 to $7,000
A 400-amp service is for a large house, a house with two air conditioners, a pool, a hot tub, and an EV charger, or a house with a large addition. It is not common in Fort Pierce, but we do it when the load calculation calls for it.
Federal Pacific or Zinsco panel replacement: $2,000 to $5,000
A Federal Pacific Stab-Lok panel and a Zinsco panel are both known defects. The breakers can fail to trip. That is a fire risk. Many insurers will not insure a house with one. A four-point inspection will flag it. The fix is replacement, not repair.
Read more: Federal Pacific Panel in Fort Pierce and Zinsco Panel in Fort Pierce
Subpanel: $800 to $2,000
A subpanel adds breaker spaces where the main panel is full. It does not add service size. If the main service is too small, a subpanel does not fix it. A panel upgrade does.
How much is an EV charger installation?
Total for most homes: $1,000 to $3,500
That includes the charger, the circuit, the permit, and the labour, for most homes. The average is around $2,000.
A basic install is $850 to $1,750. A complex install is $2,750 to $7,200. Complex means a long run from the panel, a panel upgrade, or a difficult route through the house.
What moves the price up: a 100-amp panel that cannot carry a Level 2 charger, a long run from the panel to the garage, and a permit. We do a load calculation first. We check the panel before we quote the charger.
How much is a whole-home surge protector?
Typically $200 to $800 installed. A panel surge protector alone is $250 to $500. The range depends on the type of protector and whether it is installed with a panel upgrade or on its own.
A whole-home surge protector sits at the panel and guards the whole house. It does not replace plug-in strips. It sits upstream of them. In a lightning-prone area like Florida, it is cheap insurance for a fridge, an air conditioner, and a television.
How much is a generator hookup?
Portable generator, inlet and interlock: $500 to $2,400
An inlet and an interlock let you run a portable generator safely. The interlock stops the generator from backfeeding the grid. That is the rule that keeps line workers safe. Never backfeed a generator. Never plug a generator into a wall outlet.
Manual transfer switch subpanel: $1,500 to $2,500
A transfer switch subpanel lets you choose which circuits the generator powers. It is more expensive than an interlock, and it is cleaner to use.
Standby generator, 11 to 14 kW: $6,500 to $9,500
A standby generator starts on its own when power goes out. An 11 to 14 kW unit powers the essentials — fridge, lights, a few circuits, and in some cases one air conditioner.
Standby generator, whole-home 18 to 24 kW and up: $9,500 to $18,000
A whole-home standby generator powers the house. The size depends on the load calculation. Fuel, pad, and permit are part of the price. We do the load calculation first.
How much is a full home rewire?
Typically $8,000 to $20,000. A single-storey house in Tampa Bay is often $12,000 to $25,000, and Fort Pierce is in the same range for a larger or harder house.
What moves the price up: house size, number of circuits, access, plaster walls, and a panel upgrade at the same time. A rewire takes days, not hours. We tell you the time and the price before we start.
How much is aluminum wiring remediation?
Typically $1,500 to $4,000. For a 1,500 square foot home, $1,800 to $3,500 is common.
Aluminum branch wiring was used in houses built from 1965 to 1973. The fix is approved connectors at every connection, or a full rewire, depending on the house. A licensed electrician has to see the wiring to price it. Do not let anyone quote aluminum remediation without opening boxes.
How much are small repairs?
Outlet replacement: $95 to $150
One outlet, replaced with a screw connection, tested before we leave. Backstabbed outlets are replaced with screw connections.
GFCI replacement: $95 to $200
A GFCI in a kitchen, a bathroom, outdoors, or by a pool. A GFCI protects people from shock. Do not replace it with a standard outlet.
Breaker replacement: $150 to $300
One breaker, replaced and tested. If the breaker trips again, the fault is not the breaker. We test the circuit.
Ceiling fan: $200 to $500
A new fan, on a fan-rated box, not a light box. That is the part people skip, and it is the part that matters.
Call Now to Speak to a Specialist
Call (877) 631-1186 — 24/7, English only. We respond fast — just a call away.
What moves the price up — and down?
Up: a panel in bad shape, corrosion, hard access, a long run from the panel, a permit, a meter pull, and a job that needs a rewire instead of a repair.
Down: a clean panel, short runs, easy access, and a job we can see clearly before we quote it.
The biggest factor is the panel. A clean 200-amp panel with open spaces makes every job cheaper. A full, rusted, or defective panel makes every job more expensive. That is why we look at the panel first.
Fort Pierce: why costs are what they are
Fort Pierce houses are older than many people think. A lot were built in the early to mid 1980s, and many were built in the 1970s. Older houses have older panels, aluminum wiring, and 100-amp services. That means more panel work, more remediation, and more permits than a new subdivision.
Salt air is the other factor. Outdoor panels, meter bases, and dock equipment wear faster near the water. We see corrosion in boxes on Hutchinson Island and South Beach that we do not see inland. Corrosion adds time and parts.
Storms are the third factor. A surge protector and a generator hookup are not luxuries here. They are part of living in Florida.
Do you offer free estimates?
No. We do not offer free estimates. We respond fast — just a call away. We diagnose the job, then we give you a price in writing before we start. That price is the price, unless we find something we could not see before we started. If we do, we tell you before we do the extra work.
How to get your exact price
Call (877) 631-1186. Tell us the address, what is wrong, and what you want done. We will ask a few questions. Then we will book a visit. On site, we test, we find the fault, and we give you a price in writing before we start.
Read more about our services: Emergency Electrician in Fort Pierce, Electrical Repair in Fort Pierce, Panel Upgrades in Fort Pierce
Frequently asked questions
Why do prices vary so much between electricians?
Because houses vary. A panel upgrade in a clean house is not the same as a panel upgrade in a house with corrosion and a long meter run. A quote without a load calculation and without seeing the panel is a guess. Get the price in writing, after the electrician has seen the job.
Should I hire the cheapest quote?
Not on price alone. A cheap quote with no license number, no permit, and no breakdown is a red flag. Get the license number in writing. Our number is EC13022015. Get the price in writing. Ask what is in it — labour, parts, permit, inspection.
Do I need a permit, and is that in the price?
A panel upgrade, a new circuit, a subpanel, an EV charger, a generator hookup, and a full rewire normally need a permit. We include the permit in our price, and we pull it. The City of Fort Pierce handles permits inside city limits. St. Lucie County handles permits outside the city.
What if the job costs more than the quote?
We tell you before we do the extra work. If we find something we could not see — a corroded wire behind a wall, a panel that is worse than it looked — we stop, we show you, and we price the extra work. We do not do extra work and bill you later.
Call us
Call (877) 631-1186 — 24/7, English only. We respond fast — just a call away.
Sunrise City Electric, 2250 N US Highway 1, Fort Pierce, FL 34946 (office only, not walk-in). License EC13022015. Licensed and insured. 15 years in business. Owner: Michael Bennett.